Ask a cable engineer where failures happen and the answer is rarely “the cable”. It is the joint. The terminations. The accessories, where the insulation is cut back, where a barrier was hand-assembled or machine-applied, where the environment finds a path in. A cable run between two well-made terminations is usually the most reliable part of the circuit.
VLF testing stresses the accessories as part of the cable, and partial discharge can often point to a defective one. This article covers what a VLF test proves and does not prove about joints and terminations, and what preparation the test needs to mean anything.
Key takeaways
- Accessories — joints and terminations — fail more often than the cable itself.
- A VLF withstand stresses the joint body as insulation in series with the cable, so internal defects are tested.
- It does not test mechanical integrity, external surfaces, or the air-side of a termination beyond what the field reaches.
- Partial discharge is the diagnostic most likely to single out a defective accessory.
- The first accessory test is only as good as the assembly and cleanliness that preceded it — and a re-termination should be retested at a controlled level.
1. Why accessories dominate failures
A cable left on a drum in a clean factory is a controlled product. A joint is made in a trench, by hand or by a portable machine, in weather, on a cable that may already be partly damaged, under time pressure. Every one of those factors is a way for a defect to enter.
The recurring failure mechanisms in accessories are:
- Workmanship — incorrect cut-back dimensions, damaged semiconductor screens, uneven or contaminated interfaces.
- Moisture — ingress at a poor seal, especially in joints that rely on a moisture barrier.
- Contamination — dust or fingerprints trapped at an interface, which become discharge sites.
- Mechanical damage — from installation, backfill, or later excavation.
Because these defects concentrate the electric field, they are also the defects most likely to show up as partial discharge — which is what makes accessories a natural target for a diagnostic test.
2. What a VLF withstand covers in a joint
The joint body is insulation in series with the cable insulation. When a VLF test voltage is applied between the conductor and the shield, that voltage appears across the joint as well as across the cable. Any internal defect in the joint — a void, a poor stress-control electrode, trapped moisture, a damaged screen — is stressed, and a weak joint can fail the test or trip it.
Terminations are tested in the same way: the voltage is applied from the conductor to the shield or ground, so the internal insulation of the termination and its stress cone are stressed along with the cable.
Accessories do not get a table of their own: the joint is tested at the level set for the cable. The VLF test voltage calculator returns the acceptance and maintenance values for a given cable class in both rms and peak, which is the figure to put on the accessory schedule.
3. What VLF does not cover
It is as important to be clear about the blind spots:
- External surfaces. Pollution and surface wetting on the outside of a termination produce their own discharge paths that a conductor-to-shield test does not reproduce the same way. An outdoor termination that flashes over in rain may pass a factory-like VLF test in dry conditions.
- Mechanical integrity. VLF says nothing about whether a joint is physically sound, watertight, or correctly anchored.
- Thermal performance. No information about current-carrying capability or hot-spot behaviour.
- Very short or very small defects that only discharge above the test voltage used.
4. Preparation before testing accessories
A VLF test on an accessory is only as meaningful as the state the accessory was left in. Before energising the test set:
- Confirm the assembly was completed and inspected — this is not a substitute for construction QA, it is a check on top of it.
- Ensure the joint or termination is clean and dry, and that interfaces are undisturbed.
- Verify the shield and ground connections are correct and secure; a poor ground path adds noise and can mask discharge.
- Isolate the far end and post the working area; a VLF test applies a lethal voltage across the whole run, not just the accessory.
5. Using PD to single out a defect
The withstand test may pass a joint that still contains an active defect — the defect discharges but does not bridge the insulation, so the cable holds. Adding partial discharge measurement is how the defect is seen. A joint that discharges at a low inception voltage, or whose PD grows steeply with test voltage, is a repair candidate even though the withstand passed.
Tan delta is the complementary diagnostic: an accessory with moisture ingress or a degraded interface often shows elevated loss. See VLF partial discharge testing and VLF tan delta testing for how each is read.
6. Retesting after a re-termination
When a joint or termination has been replaced, the cable is retested — but not necessarily at the full acceptance voltage. The section on either side of the new accessory is the same cable it was before, and it may be aged. The usual practice is to test at the maintenance level (generally a lower multiple of U0 than a new installation) long enough to prove the repair, so the new accessory is verified without using the opportunity to over-stress good, older cable.
The voltage question for that retest is the subject of VLF test voltage selection, and the full sequence for closing out a repair is covered in VLF testing after cable repair.
7. The point of the test
Most cable failures are accessory failures. A VLF test that stresses the accessory as well as the cable, and a PD measurement that can single out the one that is discharging, together give a far better picture of circuit health than a cable-only proof test. The method is not a guarantee — it will not catch an external surface problem or a mechanical fault — but it targets the part of the system that fails most.
Frequently asked questions
Why do joints and terminations fail more often than the cable?
Because they are assembled in the field. Workmanship, interface and moisture defects concentrate in accessories, which is why they dominate failure statistics even though the cable length is far greater.
Does a VLF withstand prove a joint is sound?
It proves the joint holds the test voltage. It does not, by itself, prove the absence of a partial-discharge-active defect, which is why PD is used alongside the withstand where a joint is the concern.
What should be done before testing accessories?
Confirm preparation – cleanliness, correct assembly, and ground continuity – and that the accessory is rated for the test voltage. After any re-termination, retest the accessory.
